Will there be any 'Arrow' mark in a Fuse holder?


Hi Everybody, I am new to this Forum. Please clarify that,

Will there be any 'Arrow' mark in a fuse holder to show

the direction to fix a fuse? Will all type of fuses have

'Arrow' mark? I need the advices to upgrade the fuses.

In one of a forum, I read the following 'Message'as follows:-

"The fuse has to be parallel to the overall direction of the sine waves coming from the wall socket and into you audio gear. If they enter at an unusually steep angle, the top (or bottom) peaks and throughs will get clipped off or attenuated and you will get jagged or almost square waves in you signal. The resulting SQ will be harsh and grating to the ears. Prolonged usage may damage the speaker coils as well."

So, friends,please give me a clear picture to replace a

'fuse' in my Preamp and DAC. Thank you.

Regards,

Rhapsodi.
rhapsodi
Geoffkait: "The subject matters to the "skeptics" only to the extent that it's another opportunity to suggest that blind tests would *prove* the damned thing doesn't work."

Actually, in my case I'm looking for proof that it does work. There's nothing that I have seen to suggest to me that changing the direction of a fuse will change the sound. Based on that I think it makes perfect sense for me to automatically assume that "the damned thing doesn't work" as you put it.
My integrated has a fuse holder at the back, so I can access the fuse without opening the case. Tonight I'll swap the fuse around and see if I hear a difference.

Are you guys talking about the AC mains fuse?
Sid, my feeling is that a blind test would be unlikely to accomplish anything.

Most blind tests that have been reported in the past, involving things that would seem more likely to make a perceivable difference than fuse orientation (such as cables and even amplifiers), have resulted in a finding that no differences were perceivable.

Assuming that would be the outcome, the believers would allege that the skeptics did not hear a difference because of negative placebo effect (i.e., they did not expect to hear a difference so they did not). They would also claim, perhaps with some legitimacy, that they themselves did not hear a difference due to lack of familiarity with the sound of the system, or due to listener fatigue that might develop during the course of the tests, or due to other aspects of the test conditions.

Also, I would not characterize conducting such a test as "easy." Eliminating the possibility of differences being caused by extraneous variables, such as the ones I mentioned in my earlier post, would require very careful control of a lot of things. And at least several test subjects would have to be involved, to eliminate the possibility that the test result might be the result of guesswork (while not requiring any individual listener to go through an unreasonable number of trials, that might lead to listener fatigue). The inclusion of several test subjects again raising the issue of lack of adequate familiarity with the sound of the system.

Sebrof, yes we are talking about the ac mains fuse on the component. My suggestion would be that if you think you hear a difference, go back and forth a couple of times to confirm (allowing a few minutes for warmup between each reversal).

Best regards,
-- Al
I find it's harder to be skeptical if there is a rational hypothesis provided that's at least loosely grounded in the physics, acoustics, or material sciences.

How a fuse that's conducting AC, especially one that's not in the signal path, can have a real affect the sonics escapes me.

Should be able to measure SOMETHING about the fuse's conductive differences, right? Those of you with means, and one of these exotic fuses in mention, O-scope the fuse's A.C.(60Hz) input and output (with your component powered up), then flip the fuse and measure again!
Bdgregory, I too find I am skeptical without some explanation for why a tweak might work, but I am also convinced by a demonstration. I have heard nothing that would explain why fuse direction would matter, nor why there might be differences between fuses except for the materials in fuses, etc. My experiences with tweaks run the gamut from worthless, such as copper tubing over the pc entering the IEC, to minimum value, such as the Brilliant Pebbles, to a great improvement, such as isolating the pcs from the floor and walls, and variable tweaks, such as quartz disks made by Acoustic Revive and others. In some placements, they do nothing, in other they do wonders, and yet in others they are terrible.