tls49
Responses from tls49
| Newbie - Replacing front speakers & going 5.0! Advice needed :) dan89 I suggest you look at specifications on Monitor Audio's website, mainly the "Recommend Amplifier Requirements" for those different models. The Bronze 2 is 30-100, however the Silver 500 is 80-250. I'm sure that Yamaha receiver works fine wit... | |
| Zu def 4 are they the best speaker made? I have also heard a few ZU speakers and none of them sounded bright or forward. It’s all about the combination of components used, system senergy.52tiger, agree, the Def 4 is one of the most lifelike speakers I have ever heard and I have listened ... | |
| Planning your Total eclipse party? Avoid being a human Sacrifice! Like mesch, I'm fortunate to live in the center of the path and my backyard will get 2 minutes and 36 seconds of total eclipse. And now a couple of corny jokes for the occasion.How do you organize an eclipse party?vvvYou planet.How does the man in... | |
| Always spend whats nessercery on high end cables they can make ahuge difference It has always made sense to me to use whatever cable the manufacturer used in the design and voicing. | |
| Need advice regarding B&W center channel to match B&W802D's HTM4D for 802DHTM4D2 for 802D2I'm sure there wouldn't be a huge difference, but it just makes common sense to stay with the same series. | |
| (One more) Dedicate power line: twist questions, oxygen-free, and code questions. As far as keeping analog and digital separate, my understanding is 2 separate outlets, each having it's own separate run back to the panel box on separate breakers. Key word is separate. Jumping one outlet to another or braiding is not separate. A... | |
| Efficient bookshelf speakers for my office Sorry soix, I must agree with auxinput. Rated sensitivity of the JA RM7 is 86db, however it was measured at 84.5db. That alone makes it unsuitable for a low powered tube amp. The other characteristics are irrelevant. With 8 watts, I would only rec... | |
| Insuring your Audio Room? Assuming you mean insurance as in your homeowners policy. A basic policy will have limits for different categories and all electronics will likely be grouped together. If you want to be fully covered, make a list of everything in the room with ass... | |
| McCormack dna1 to Sony 1040 Without an exact model number of the Sony, all answers are just speculation. Assuming it is the STR-DN1040, then your options are practically non-existent. Sorry auxinput, I must disagree with your solution to use Zone 2. If you look closely at th... | |
| mcintosh c2600 and ma6600 question 1. Yes2. See #33. You will need to remove the jumpers between Output 1 and PWR AMP on the MA6600. Then use a cable to connect the output of the C2600 to PWR AMP on the MA6600. All sources will need to be disconnected from the MA6600 and connected ... | |
| Getting an outlet to grip better.. An "audiophile" outlet should provide better contact. This is generally achieved by increased contact area and pressure. If the outlet has a very weak "grip", then it may be defective or just a poor design. Either way it should be replaced. | |
| 12 volt trigger not working Have you looked at the preamp's manual? It appears the 12v trigger has an adjustable delay. Did you wait long enough for it to activate? | |
| Hooking up an integrated to a subwoofer The simplest way would be to use a Y adapter like this,https://www.amazon.com/Mediabridge-ULTRA-RCA-Y-Adapter-Inches/dp/B004EBX5GW/ref=sr_1_4?s=electronics...Remove the jumper between "preamp out/amp in" , then connect the 2 males of the Y adapter... | |
| Using Klipsch Heresy 3 as rear channel? I definitely would not have the Heresy,s sitting flat on the floor. Using a Heresy slant riser on them might work OK depending on the distance behind you. Also, an old trick from years ago would be to face them at the back wall or into the corners... | |
| LED replacement on PrimaLuna Amp/Integrated advice? Just cut a small circle from black electrical tape and cover it. The glow of the tubes tells you when it's on or off. |