I avoided tube hifi for years as I also thought tubes would be a chore and wear out. They are sort of, and they do…and I'd been messing with tubes for decades in guitar amps. Then I realized I LIKE to mess with hifi stuff, and fell into tube hifi through a Jolida amp (I'd heard other tube stereo amps, but not enough of them seemingly). Primaluna amps are well regarded and I like their ability to switch to "triode" mode, and there is something about the linearity of tubes in a well sorted amp along with the 2nd order harmonic musicality that is more suited to my tastes. Note how often descriptions of SS amp designs claim they're "tube like." I've gone over to the "dark side" of tubophilia (!) with the single ended amp I just bought, and it's the best sounding amp I've owned…fun…just fun...
Pass Labs XA30.5 in my system?
Dear Audiophiles!
I am looking for a solid-state class A power amplifier with balanced circuit topology to replace Acurus in my modest Hi-Fi setup:
Mac mini (USB3 output) ->
Singxer SU-1 ->
Yggdrasil DAC (AES/EBU XLR input) ->
Primare PRE30 preamplifier (AES/EBU XLR input) ->
Acurus A250 power amplifier (RCA input) ->
Monitor Audio RS-6
I am currently considering Pass Labs XA30.5 and am wondering if it will “work nicely” with my upstream and downstream components.
Any info/advice is very much appreciated. Please chime in!
Please see the specs below for your consideration.
Pass Labs XA30.5
Type: Solid-state stereo amplifier
Power Output: 30 wpc into 8 Ohm, 60 wpc into 4 Ohm (both 14.8dbW)
Power Consumption (Watts): 238
Temperature (deg C.): 53
Voltage Gain: 26 dB
Input Sensitivity: 0.77 V at 26db gain
Frequency Response: 1.5Hz–100kHz, –3db at 1.5Hz, –2db at 100kHz
Signal/noise: 150db at full power (I cannot believe this is not a misprint!)
Distortion: 0.01% at 3 watts, 0.1% at 30 watts (measured at 1 kHz)
Input Impedance: 30 kOhm balanced, 15 kOhm unbalanced
Damping Factor: 150 for an 8 Ohm nominal load
Maximum Output Current: 20 Ampere
Maximum Output Voltage: ±35 Volts
Output Noise: 150 microvolt unweighted 20 Hz - 20 kHz
DC Offset: <50 mV
Slew rate: ±50 V/µs
Dimensions: 19" (485mm) W by 7" (180mm) H by 19" (485mm) D
Weight: 62 lbs (28kg)
Shipping weight: 75 lbs (34kg)
Primare PRE30 Preamplifier
Balanced inputs 560mV
Line inputs 280mV
Sensitivity adjustment -20dB to +20dB
Tape outputs 280mV
Gain 16dB
Frequency response DC to 100kHz ± 0.1dB
THD <0.01%
Signal-to-noise ratio -118dB
Crosstalk -113dB
Mains 100/115/230V
Dimensions (WxDxH) 430 x 410 x 100mm
Weight 9.5kg
Monitor Audio RS6
Frequency Response: 38 Hz - 30 KHz
Sensitivity (1W@1M): 91 dB
Nominal Impedance: 6 Ohms
Power Handling (RMS): 120 W
Recommended Amplifier Requirements (RMS): 40 - 120 W
Tweeter Crossover Frequency: 3 KHz
Drive Unit Compliment: 1 x 6” C-CAM® Bass, 1 x 6” C-CAM® Bass Mid-range. 1 x 1” gold dome C-CAM® tweeter.
Cabinet Design: Balanced velocity twin reflex ported
Product External Dimensions: (H x W x D) 850 x 185 x 250 mm
Plinth Dimensions: (H x W x D): 25 x 255 x 305 mm
Individual Weight: 18 Kg
N.B. Impedance varies with frequency and goes to as low as 4 Ohms and as high as 16 Ohms. And, most importantly,“real” sensitivity is much lower than “nominal”: 87.40dB (averaged 300Hz-3kHz, 2.83V/1m)!
Measurements taken in the anechoic chamber at Canada's National Research Council can be found through this link:
http://www.soundstagenetwork.com/index.php?option=com_content&view=article&id=1221:nrc-measu...
I am looking for a solid-state class A power amplifier with balanced circuit topology to replace Acurus in my modest Hi-Fi setup:
Mac mini (USB3 output) ->
Singxer SU-1 ->
Yggdrasil DAC (AES/EBU XLR input) ->
Primare PRE30 preamplifier (AES/EBU XLR input) ->
Acurus A250 power amplifier (RCA input) ->
Monitor Audio RS-6
I am currently considering Pass Labs XA30.5 and am wondering if it will “work nicely” with my upstream and downstream components.
Any info/advice is very much appreciated. Please chime in!
Please see the specs below for your consideration.
Pass Labs XA30.5
Type: Solid-state stereo amplifier
Power Output: 30 wpc into 8 Ohm, 60 wpc into 4 Ohm (both 14.8dbW)
Power Consumption (Watts): 238
Temperature (deg C.): 53
Voltage Gain: 26 dB
Input Sensitivity: 0.77 V at 26db gain
Frequency Response: 1.5Hz–100kHz, –3db at 1.5Hz, –2db at 100kHz
Signal/noise: 150db at full power (I cannot believe this is not a misprint!)
Distortion: 0.01% at 3 watts, 0.1% at 30 watts (measured at 1 kHz)
Input Impedance: 30 kOhm balanced, 15 kOhm unbalanced
Damping Factor: 150 for an 8 Ohm nominal load
Maximum Output Current: 20 Ampere
Maximum Output Voltage: ±35 Volts
Output Noise: 150 microvolt unweighted 20 Hz - 20 kHz
DC Offset: <50 mV
Slew rate: ±50 V/µs
Dimensions: 19" (485mm) W by 7" (180mm) H by 19" (485mm) D
Weight: 62 lbs (28kg)
Shipping weight: 75 lbs (34kg)
Primare PRE30 Preamplifier
Balanced inputs 560mV
Line inputs 280mV
Sensitivity adjustment -20dB to +20dB
Tape outputs 280mV
Gain 16dB
Frequency response DC to 100kHz ± 0.1dB
THD <0.01%
Signal-to-noise ratio -118dB
Crosstalk -113dB
Mains 100/115/230V
Dimensions (WxDxH) 430 x 410 x 100mm
Weight 9.5kg
Monitor Audio RS6
Frequency Response: 38 Hz - 30 KHz
Sensitivity (1W@1M): 91 dB
Nominal Impedance: 6 Ohms
Power Handling (RMS): 120 W
Recommended Amplifier Requirements (RMS): 40 - 120 W
Tweeter Crossover Frequency: 3 KHz
Drive Unit Compliment: 1 x 6” C-CAM® Bass, 1 x 6” C-CAM® Bass Mid-range. 1 x 1” gold dome C-CAM® tweeter.
Cabinet Design: Balanced velocity twin reflex ported
Product External Dimensions: (H x W x D) 850 x 185 x 250 mm
Plinth Dimensions: (H x W x D): 25 x 255 x 305 mm
Individual Weight: 18 Kg
N.B. Impedance varies with frequency and goes to as low as 4 Ohms and as high as 16 Ohms. And, most importantly,“real” sensitivity is much lower than “nominal”: 87.40dB (averaged 300Hz-3kHz, 2.83V/1m)!
Measurements taken in the anechoic chamber at Canada's National Research Council can be found through this link:
http://www.soundstagenetwork.com/index.php?option=com_content&view=article&id=1221:nrc-measu...
- ...
- 37 posts total
- 37 posts total