What 5ch or 3/2 to match Aragon 8008bb?

Hi Kincade
To my knowledge the 4004 Doesn't get close to the 8008BB. Re: triggering - You do have to turn them on manually - when they're off - they're off. No stand by. I happen to like that.
I would go with the seperate amps. Two reasons. 1. Much better chanel seperation. Not to mention that you will have MUCH more actual current, available per channel. 2. IF by chance a channel goes bad somehow, you are not completely "out of business". Let me know how things go.
Paul

Kincade,

You have to manually turn them on. I had a 4004 markII and an 8008BB (pre-klipsch). I dumped them both and picked up a sherbourn 7/2100 and haven't looked back. Processor is an Anthem AVM20 and speakers have included B&W N805's and N805Sigs, VR4jr's and Soliloquy 5.3i's. Cables are cardas golden cross and sources are Xindak SACD2 and modded Philips 963SA.

Good luck,

Shayner

Thanks; I wondered if there was a difference between the Acurus and Aragon, and if it was noticeable.

Oldpet,

Thanks for the responses; Do you just leave the amps on all the time, or do you turn them on every time you listen?

PRPixel,

So you're saying that there is NO difference between the Sherbourne 7/2100 (class A/G), and the Aragon 8008bb? Because if that's true, I can hang on to my brand new Sherbourne and save about $1200, which would go quite a ways towards other equipment. I just read more and more about the switching to class G, and I cant see how it WOULD be in the same league as the 8008. Please elaborate, I'm very interested in your opinion on this.

Your speakers are almost exactly what I will be getting (currently Dahlquist QX10's, but will be going w/ VR4jrs soon); and the pre-pro is an AVM-30. Sources are a Denon 2900 and Jolida JD-100 CDP.

Basically, I have similar setup:

-8008BB for mains.
-8008x3 for the center and 2 surrounds
-4004 markII for rear surrounds
-Vandy speakers through-out

I am very happy with my setup & have no plan to upgrade for a long time. Recently I added an Aragon 8008X3 to my system and I love it, it matches extremely well with the 8008BB. The system seemingly unlimited power, transparency and great dynamics. Also I'm considering an Aragon 8008X3 is one of the best buy (used $1350-1400).

Good luck.

Hi Kincade:

DO NOT leave your Aragon amps on all the time. I don't know if anyone else can attest to the same sort of experience, but I didn't pay much attention when I first had my 8002, so I left it on all the time. Aragon amps tend to be havily biased into class A, and I didn't realize my little 8002 drew 1000watts just sitting there doing nothing. My first $400 electric bill(for ONE month)
stopped me from doing that. Besides, they only need about 10-20 minutes to warm up and sound their best anyways.
By the way, all "Class A" amps switch to class A/B when putting out more than several watts(varies a bit). The reason the 8002 and 8008 pull so much idle current is because they are heavily biased into A, which is very inefficient, but switch to class A/B probably when output exceeds around 10-20 watts. I can explain more if you wish to be bored to tears sometime. Oh, and I have had a
Sherbourne 5/1500 connected to my JM Labs Electra 936 speakers a while back, and it was ok. Haven't heard the one you have, but the one I heard simply couldn't keep up with my 8002, let alone my 8008BB. Frequency extremes were where the Sherbourne seemed a little lacking. Still, if your only going to use it for non-critical listening, it would be good for a hometheater. I'm also a fussy pain-in-the-butt 2-channel snob, so take my advice with a grain of salt. Using the Sherbourne for the surrounds? Probably should stick with it and save some cash. $1200 buys a lot of movies! Whatever you decide, good luck, and ENJOY...

Shayne.