low-level background white noise - Parasound Halo JC-3+


Summary:
I’ve got an issue with the background noise that I can’t seem to figure out. It’s white noise, there is no 60 hz hum present at all. So, I don’t think it’s a grounding problem. If I turn up the JC-2 on the JC-3+ input to 100%, I get 61db of white noise (c-weighted, slow response) from the listening position (about 12 feet from the speakers). There is a faint 60-hz component, but it’s mostly white noise. (It’s not pink noise). That test is with the tonearm cable disconnected from the system. 

My system:
Me: 51 year old 30-year audiophile with tested 35 year-old ears. Excellent hearing in both ears.
Linn LP-12 Radikal/Keel/Ittok LVII/Dynavector XX2Mkii/Audio Origami phono cable
JC-3+ set in the MC Variable position at 100 ohms loading
JC-3+ with Belden XLR cables to the JC-2 as well as Goertz single-ended cable (A/B testing)
The rest of my system is a Linkwitz LX-521 based system driven by Emotiva XPA-5 Gen 2 amps in an analog active cross-over config. It’s irrelevant to this conversation in my opinion.

Here’s my problem:
Parasound JC-2 on input 1 with the volume control set at the 9 o’clock position. (or 25%). This is normal volume and produces about 75 db music at the listening position. White noise is clearly present, I’d estimate it at the 50 db level. It’s about the same level as when the HVAC is pulling air through the vents.
Inputs on the JC-2 positions two thru six are dead silent all the way to full volume.

Here’s my test chain of events:
Disconnect the 90 degree connector from the LP-12. White noise still present.
Disconnect the Audio Origami phono cable completely. Connection from JC-3+ to JC-2 only via XLR. White noise present.
Replace the XLR cables with RCA cables. White noise present. Substitute different XLR cables, white noise present.
No cables on input one of the JC-2 (JC-3+ disconnected). No white noise present. Dead silent.

I tried reversing polarity via the switch on the JC-3+, but this doesn’t help.
Both channels have the exact same level of white noise in all of the above tests.

Any ideas? Is this normal? Am I being too critical? Is there something I haven’t thought of? 
marktrav
I also have a JC3+ and am running it with a Voxativ integrated and mine is also dead silent.  If your ground is good then you must have an issue with the unit itself????

Good luck!
Have you tried using your amp, ASP or DSP, JC2 with the LX521's while playing a cd or digital file?  

If so, does the noise still appear?  

I have the same preamp, with the Linkwitz ASP and Orions, and there is a very low level noise just barely audible within a foot of the speakers, which I've traced to the ASP.  
  • Not related to this strand but I happened to be reading a dec post were you commented that you had an ref 3 that could be for sale. I've been looking for ref 3 or 5 at fair price to replace ls26 that I will sell. 
  • Doesn't seem like arc gear selling quickly at the moment
I just realized I never followed up to this thread. I sent the unit to Parasound and they tested it and it met spec. Absolute first class warranty service. There was nothing wrong with the unit. It turned out to be the amps. I was using Emotiva XPA-5 Gen 2 amps. I upgraded to the ATI AT524NC amps, and all the background hiss I was hearing disappeared. Perhaps the synergy between the JC-3+ and the Emotiva wasn't great. I've since fallen back in love with the JC-3+ and have no plans to do anything with it.