Jmcgrogan2 - thank you so much - super helpful - I'm actually pretty bummed - should say super bummed - got my Magico S5 set up and I mean everyone says how incredible they are - I have a first rate source - Bricasti M1SE - first rate amp - Pass Labs X350.5 which is known to be a pretty warm amp - HiDiamond D8 Speaker Cables which are not Nordost Oden but very nice copper cables and quite compitant, Verestarr Grand Illusion Signature IC's which are also very nice and even a bit warm and these Magico's are burning a whole right through my head like a lazier beam. I've been setting them up and measuring and tweaking and they are giving me a royal head ache? How can this be? These are top rate speakers? They make me want to buy a Cary preamp and CJ tube amp and get Cardas Golden Cross Cable Full Loom? Which I can't do and I'm sure would sound like crap? Even my wife said these don't sound as nice as your other speakers? Any advice? Maybe my bran needs to adjust but there is going to be some serious adjustment- my last speakers were total opposite of laid back - they were ultra revealing but I wasn't expecting this? Bummed to the extream but also hoping a tube pre and maybe a cable change can get these to settle down?? Maybe need to be driven a while also? Just back from Magico and had some service so maybe some new parts or something needs to break in??
PLEASE match Advice Pass Labs X350.5 (20k) to Hovland HP-100 (2500ohms) Miss-match ???
GUYS / GALS NEED YOUR HELP PLEASE!
A friend said this preamp is outstanding and will sound great with Pass Labs amps and to not get caught up in the specs but the measurements say different.
Pass Labs X350.5 amplifier with input Impedance 30k ohms Balanced or 20k ohms Single ended*
(*source Pass Labs Manual)
Hovland HP-100 source impedance 2500ohms*
(*source Stereophile)
Guys / Gals, can I used my Pass Labs X350.5 amp with Hovland HP-100 preamp? Has anyone used Pass amps with Hovland pre's. I will be using Magico S5 Speakers and Bricasti M1SE DAC but want it to sound the best it can. Should I just stick with the Aesthetix Calypso pre I was leaning toward before my gut said to go for the Hovland HP-100
Hovland HP-100 Preamplifier: * Output impedance: approximately 2500 ohms or according to Atkinson, Hovland HP-100 (2500ohms) its source impedance was high at 2.4k ohms, rising to 4.3k ohms at 20Hz. The partnering power amplifier would best have an input impedance of at least 47k ohms if the bass is not to sound lean*. The Pass Labs doesn't meet the x10 requirement it is supposed to but it is sort of close when looking at it. What do you guys think? I am not sure what to do but you guys will know what to do?
Stereophile: Its input impedance was a usefully high 100k ohms in the midrange and bass, with just a small reduction to a still-high 86k ohms at 20kHz. Despite the claim that the HP-100 uses a cathode follower output stage, its source impedance was high at 2.4k ohms, rising to 4.3k ohms at 20Hz. The partnering power amplifier would best have an input impedance of at least 47k ohms if the bass is not to sound lean.
Read more at https://www.stereophile.com/content/hovland-hp-100-preamplifier-measurements#YZXZfGLbbL2COkLR.99 https://www.stereophile.com/content/hovland-hp-100-preamplifier-measurements#YZXZfGLbbL2COkLR.99
A friend said this preamp is outstanding and will sound great with Pass Labs amps and to not get caught up in the specs but the measurements say different.
Pass Labs X350.5 amplifier with input Impedance 30k ohms Balanced or 20k ohms Single ended*
(*source Pass Labs Manual)
Hovland HP-100 source impedance 2500ohms*
(*source Stereophile)
Guys / Gals, can I used my Pass Labs X350.5 amp with Hovland HP-100 preamp? Has anyone used Pass amps with Hovland pre's. I will be using Magico S5 Speakers and Bricasti M1SE DAC but want it to sound the best it can. Should I just stick with the Aesthetix Calypso pre I was leaning toward before my gut said to go for the Hovland HP-100
Hovland HP-100 Preamplifier: * Output impedance: approximately 2500 ohms or according to Atkinson, Hovland HP-100 (2500ohms) its source impedance was high at 2.4k ohms, rising to 4.3k ohms at 20Hz. The partnering power amplifier would best have an input impedance of at least 47k ohms if the bass is not to sound lean*. The Pass Labs doesn't meet the x10 requirement it is supposed to but it is sort of close when looking at it. What do you guys think? I am not sure what to do but you guys will know what to do?
Stereophile: Its input impedance was a usefully high 100k ohms in the midrange and bass, with just a small reduction to a still-high 86k ohms at 20kHz. Despite the claim that the HP-100 uses a cathode follower output stage, its source impedance was high at 2.4k ohms, rising to 4.3k ohms at 20Hz. The partnering power amplifier would best have an input impedance of at least 47k ohms if the bass is not to sound lean.
Read more at https://www.stereophile.com/content/hovland-hp-100-preamplifier-measurements#YZXZfGLbbL2COkLR.99 https://www.stereophile.com/content/hovland-hp-100-preamplifier-measurements#YZXZfGLbbL2COkLR.99
- ...
- 111 posts total
- 111 posts total