2. amps-preamps
  3. 138255-3568

RCA to XLR vs XLR to RCA... Converting Input or Output - Does It Matter??

I just picked up a new DAC that only has RCA outputs whilst my preamp only has XLR inputs.  realizing that a DI box like the Jensen ISO-Max is the proper way to resolve this incompatibility, that's not an immediate solution for me.  in the short term, i was going to use adapters on either the DAC outputs or the preamp inputs.  given the following options, is there any benefit to one vs the other (emi/rfi, noise, etc)...

Option 1:
convert the RCA output on the DAC to XLR via an RCA Male to XLR Male adapter and connect the components using an XLR cable.

Option 2;
convert the XLR input on the preamp to RCA via an RCA Female to XLR Male adapter and connect the components using an RCA cable.

as an alternative to the above, i could also use a converter cable, RCA male to XLR male as a short-term solution.

i know none of the above will turn an unbalanced signal to balanced - these are really only to address jack incompatibilities - and the proper solution is a transformer.  until i'm able to implement that, is there a preferred method from those above?

thanks for any inputs.  
128x128srosenberg
sbank's avatar
sbank
2,038 posts
 
Which Jensen ISO-max model would even do the job? I don't see one that accepts RCA inputs and has XLR outputs. I've just switched to a single ended Nagra phono stage and am feeding its output into my BAT balanced line stage. Currently I use a pair of single ended cables from the Nagra output and convert via Neutrik adapters at the BAT XLR inputs. Understanding that theoretically "adapters are bad" and add a potential point of entry to noise, what would be a better approach? Perhaps having a cable made that's RCA to XLR within the cable? Don't see too many of these being offered, but I can probably have one made using Mogami cable or something similar...
FWIW, at least the Nagra is battery powered, eliminating any AC noise at the phono stage. Cheers,
Spencer 
Ag insider logo xs@2x
gdnrbob
2,421 posts
 
@sbank 
It isn't listed, but Jensen can make one for you. PC-2XR

http://www.jensen-transformers.com/product/pc-2xr/
They have great customer service.
B
almarg's avatar
Ag insider logo xs@2x
almarg
8,673 posts
 
Bob, to be sure it’s clear, while Spencer wants to convert RCA inputs to the transformer to XLR outputs from the transformer the PC-2XR will do the opposite. Spencer, the PI2-RX would be suitable. You can find it at the following link at a slightly better price than if it is ordered directly from Jensen. (Choose RCA input connectors in the drop-down menu near the bottom of the page).

https://www.cs1.net/products/jensen_transformers/PI-2XX.htm

Note that this device requires XLR cables on its output side that are short (e.g., one or two feet or so), and do not have high capacitance per unit length. The RCA cables on its input side can be any reasonable length.

A single-channel version (PI-RX) is also available, for use with monoblocks.

SRosenberg, I doubt that which of the two options you described would be best can be predicted with any certainty, and I suspect that whatever difference might result would be component and cable dependent. And very conceivably there may be no difference at all.

Best regards,
-- Al
inna
5,245 posts
 
Do you lose gain when using adapters ?
Purist Audio can custom make any cable you could imagine and beyond that. For the price.
srosenberg's avatar
srosenberg OP
209 posts
 
@sbank as was already mentioned, Jensen can configure their transformers RCA to XLR or XLR to RCA - take note of the order of the X and R in the product ID as this will indicate the ins and outs.  there are three units: PI, PO and PB as detailed here: https://www.cs1.net/learn/jensen_transformers_application_guide.htm

And as Inna mentioned, you can have cable made from a number of places... PAD, BlueJeans, Benchmark (yep, they sell cables, too).

@almarg thanks for the note... good to know there's not an absolute 'right way' to handle the jack adapters.
More to discover