VPI HW-17


I have recently re-entered the analog world, and have been using the VPI HW-17, together with a Discwasher brush and fluid, to clean my albums. This does a good job, but obviously I am not using the maching to its full potential. I am hesitant to fill the reservoir, because somehow I feel the fluid will become moldy and foul, especially in the waste reservoir. Am I being paranoid? Any recommendations on how to keep things clean?
hurricane
If you tilt machine up from the front i put hose into a jar exess fluid then runs into the jar from hose!!I keep jar on the floor below machine hope this helps.
Thanks, everybdy! I have tossed the Discwasher and just ordered the MSFL brushes. Will get back to you!
I've owned the HW-17 for about seven years now and have cleaned thousands of discs with it. Yesterday I noticed a wet spot on the underside of the particle board enclosure and opened it up to see the leak. To my dismay much of the interior is covered in black mold. The leak's been occurring at the connection between the main waste reservoir and plastic tube drain. If you look closely you can see the plastic tube is slightly elevated above the connection meaning gravity will always pool waste fluid there first, basically begging for a leak. With only a small ring clamp that would never be air or water tight, practically every HW-17 in the world will have the same problem. Did the design engineer lack common sense? I emailed VPI yesterday with photos but no response yet.

The exhaust fan operates while in use billowing out mold into the room air, so I've moved it into the garage. But this is a temporary solution, with the heat and cold swings in the garage the black mold is only going to grow exponentially now. The vacuum motor has rusted from the leak but all the electronic parts work fine still. Any recommendations on what I can do? I'd hate to throw the whole machine out because the particle board chassis is now contaminated. Here's a picture I just took. The camera flash hides the severity of the mold, but as you can see the mold is very evident and AWFUL.

[img]http://www.freeimagehosting.net/t/dve6m.jpg[/img]
Hi, If you put household bleach in a spray bottle and mist the mold it will dye, You will need a warm room with air flow. After this process starts you can wear plastic gloves and scrub the wood. If you wish the wood can then be painted. I never had this problem with mold because I chucked the vpi suction moter befor I ever used it. I added a plactic vacuum cleaner hose with a plastic hose end fitting where the other moter used to connect to the unit. I used 25 feet of this hose drilled a 11/2" hole to my basement and hooked this up to a used rainbow vacuum cleaner power unit. This machine is designed to clean with water as a filter, you would fill a water basin with 2 quarts of water befor you clean then dump water and dirt in toilet. The machine water basin is plastic, cant rust. The only things I did was insurt a plastic nipple in the hose line and drill different sizes or hold to relive the massive air flow ( suction ) to relive the pressure on the VPI suction tube , and I wired a heavy duty extension cord to the orgional connectios of the VPI motor. I have been using this for at least 20 years with out a problem and have cleand as many as 25 LP and never need to empty the water pan. I know this works. I was in the vacuum cleaner business for 50 years. Good luck with whatever you do , David.
David,

Chance you'd wanna take a job of converting mine for me as well? Course I'd cover parts, shipping, and whatever you want for labor. All in one unit versus linked hose to basement though.

With all the HW-17 VPI's in the world, surprised there isn't already a niche market for fixing this poor design. Also makes me wonder about the quality of VPI turntables, not that I'd ever want to downgrade from my idler wheel transcription tts to find out.

I notice the new VPI typhoon has a stainless steel chassis, perhaps a way of circumventing the mold problem without addressing the engineering flaws causing it in the first place? Who'd want to spend $2K on a leaky machine though?

GC