DACs: Burmester vs. Meitner vs. dcs


Any comments would be appreciated.
libor35
maybe.

i will rethink my passive approach (or at least be open-minded to an active pre). in my old room (12' x 18' with very large dynamic speakers) i was in the extreme near-field, i had the walls covered with lot's of absorbtion, there was plenty of dynamics, and plenty of bass energy in that small space. i didn't get any feeling that the passive approach left anything out. in my new room (21' x 29' x 11') i 'might' get better bass and dynamic balance with an active pre.

i 'intend' to accomodate multi-channel music. since the DAC6 is multi-channel i will install conduit for the center channel, side channels and subwoofer interconnects and dedicated power outlets for each speaker location. i would likely get an emmlabs Switchman to distribute the multichannel and integrate it with my Jena Labs switchbox as an additional input. i plan on having 2 positions for my listening chair. a 2-channel position and then a foot or so forward, a multi-channel position. this will allow me to have all the speakers equadistant from my listening chair for multi-channel. the rear speakers won't be able to be at 110 degrees, but it will be the best compromise possible with a 2-channel priority (i would need a 25 foot wide room for 110 degrees--which would result in too large a room. i might have mobile absorbtive panels i can use to optimize multi-channel since 2-channel needs more relective energy to be optimized than multi-channel.

otherwise i expect to use the same gear, cables, power cords, racks, etc. i will have an additional set of ST Optical cables run to my seating position so i can have the digital transport where i can switch discs without getting up. in my other room it was narrow enough to reach without getting up. that is one great thing about optical connections....there is virtually no loss of signal regardless of length.

i am currently debating whether i want some sort of 'power-regenerator or just go with my previous 'simple' approach. Rives Audio recommends the big Equitech Balanced A/C power unit......i like simple (20 amp dedicated circuts, 10 guage romex 'home runs' all equal length, Jena Labs cryo's duplex outlets, on both sides of the panel). stay tuned for that.....

one little point. i will install my duplex outlets upside down for my Tenor amps since my damn Elrod Statement power cords currently require a full twist to go from amp to outlet. the Elrods sound so glorious i can't complain too much......but it would be nice if they thought of such issues when they make big, unweildy power cords. i am also adding 220v outlets for future possibilies.
"i am also adding 220v outlets for future possibilies"

Adding these outlets is a stroke of genius on your part. After reading your post and glancing at your system, I am convinced that putting a washer/dryer combination in your listening room can't help but to improve the results you're getting in there.

Sincerely,

Holton Corsey
you read my mind......i kinda need a 'spin cycle'. Maytag is bringing out their own amplifiers.

actually, the Tenors are said to perform better on 220v....and so do some other amps. it's cheap and easy to install now.....even if i never use it.
this talk about 220 volts has triggered some questions are their companies which make high end 220 AC outlets? How about high end 220 voltage power cords?
Mejames,

i have no knowledge of any 'special' 220 volt outlets.....i would guess that they are typically more 'robust' than a standard 110 duplex outlet....the plug arrangement is certainly more secure with more contact area. i have a few friends that have had their power cords modified for these 220 volt applications.....there are no real challenges since the power cords already have the construction to handle it....it is just a matter of the plug.

my guess is that in many cases 220 volt operation will bypass some parts of the power supply that are necessary for 110 volt operation......this probably will lower noise and improve dynamics to some small degree. (my lack of legitimate knowledge of things electrical has likely got me over my head here......ultimately i'll deciede by listeneing).

i know when i owned my Levinson #33h and later #33 amplifiers......that changing to 220v would have improved the performance......i had heard those with 220v and they were better.

for me it is more a matter of doing this while my room is being constructed and the walls are openned up......i haven't done enough 'homework' to be certain this is something i want to do. having 220v outlets will allow me to try products from other parts of the world that have that as their native voltage.