2. amps-preamps
  3. 1407646817

Distortion with ARC Ref 150 and Maggie 3.7

I have this problem that drive me nuts for quite a while. I purchased a like new fully balanced ARC Ref 150 tubes amp through Audiogon for my single ended only CAT SL1 Ultimate preamp and connected both with a RCA to XLR interconnect. It sounded okay with most recording but has awful distortion with certain recording specifically piano and vocal. Some of this recording happens almost on entire record but some only on certain musical passage. Most of the time with higher pitch or peak of music or higher volume.

For your information I listen to vinyl only most of the time and more on Jazz music. Other component listed as follow:

Turntable: Sota Nova, Tonearm: Origin Live Illustrious, Cartridge: Dynavector XV1-S, Step up transformer: Bob's Device CineMag 1131 (Blue) feeding directly to CAT's own phonostage, Speaker: Magneplanar Magnepan 3.7. Power cords, ICs, Speaker cable, Autoformer: Paul Speltz Anti-Cable.

Trouble shooting which has been done includes: checking preamp tubes condition and checking power amp bias. Since ARC claims their Ref 150 was design for balanced preamp only so I also tested by replacing it with single ended tubes amp but the distortion remain. As for the cartridge I believe I have done the alignment pretty accurate with the Mint's Best Tractor but not very sure with the azimuth.

While tested with my other 2 pair of speakers, one which has higher spec show the same problem while the lower spec one seems get rid of distortion. So I suspected the issue probably was with the new Maggie. Called the dealer and he performed a test with his transistor amp with no distortion at all. So he assumed my Maggie is okay. Is it true that the Maggie only good with transistor amps?

By now it leaves me with total confusion! Sincerely hope fellow audiophile here could give me some advice and save me from this endless misery !

Thanks very much in advance!
pakwong
syntax's avatar
syntax
2,033 posts
 
I have to believe that single ended and balanced components does have mating problem. It seems like many balanced only component were designed to match with other similar or same manufacturer component only.

No, even when some will say, balanced needs balanced ...it is blubber. What you have is a different output or input rating, that's all. And that you can hear when the preamp output is too weak for a balanced amp input for example. But it will not create a distortion.
XLR adaptors are very simple, probably a problematic soldering can produce such a distortion but you can check it easily, you can buy these everywhere.

The Maggie is something I cannot live without. So do the CAT SL1...

Yes, true. But forget SE amps with Mags...these speakers run with nearly everything BUT they love high powered amps. The more power you give them the better they sound. The problem is, high power + good sound is nearly impossible to find. It is the way it is.
When I would run the 3.7 today, I would choose the Lamm Hybrid amps. They bite the bullet.
almarg's avatar
Ag insider logo xs@2x
almarg
8,673 posts
 
08-14-14: Syntax
No, even when some will say, balanced needs balanced ...it is blubber. What you have is a different output or input rating, that's all. And that you can hear when the preamp output is too weak for a balanced amp input for example. But it will not create a distortion.
Syntax, I suspect that you submitted this comment before seeing the preceding several responses. It is not blubber. Apparently this and some other ARC balanced amps are designed such that when fed a single-ended signal no signal voltage will be processed through "half" of the balanced signal path. That will cause the maximum output voltage of the amp to approach being only 1/2 of the output voltage corresponding to its maximum rated output. (Probably a bit more than that due to the reduced demand on its power supply). Everything else being equal, power is proportional to the square of voltage. Therefore 1/2 voltage = 1/4 power.

As I said earlier, and as the comments by Marty confirm, by providing the amp's balanced (and only) input with a single-ended signal (via an adapter, rather than via a transformer which would convert it to balanced), its 150 watt rating has most likely been reduced to not much more than 37.5 watts. Way too little for the Maggies, and an invitation to clipping distortion at typical volume levels.

Regards,
-- Al
martykl
3,563 posts
 
It's funny, because this thread is starting to feel like it will spin off much like the old thread I referenced above. Several people posting that a power amp cannot be forced to produce less output because it receives a single ended signal rather than a balanced signal. I undrstand that this result is unusual, but.....

For the record, a single ended signal via XLR adapter will cause a particular set of ARC power amps tp distort horribly at relatively low output levels. Per ARC. Per my own experience. Period.

Whether he replaces his preamp or inserts a transformer (as Al recommends) the OP needs to feed a balanced signal to his ARC amp. It's a design quirk, but once my VT 130 SE was appropriately fed, performance went from IMHO unusable (much as the OP describes) to outstanding.

My advice to the OP, don't screw around with any other fixes. ARC told you what to do about this problem. Either do it, or ditch the amp. Trust me, I've been in this precise situation and the solution is a balanced signal.
zd542
5,339 posts
 
"It's funny, because this thread is starting to feel like it will spin off much like the old thread I referenced above. Several people posting that a power amp cannot be forced to produce less output because it receives a single ended signal rather than a balanced signal. I undrstand that this result is unusual, but....."

I'm not sure I understand what you are talking about here. Wouldn't the preamp determine if the amp can be driven properly? If you had a preamp with enough gain to compensate for the difference between balanced and SE operation, it shouldn't make a difference. Or, is there something else that I'm missing?
almarg's avatar
Ag insider logo xs@2x
almarg
8,673 posts
 
ZD, yes, very uncharacteristically you are missing something :-)

Yes, there will be a gain difference. But that is not the problem. The problem is that the **output stage** of the amp will not be able to deliver much more than 1/2 of the voltage that it must deliver to reach its maximum rated output power without clipping, and therefore the amp won't be able to deliver much more than 1/4 of its rated power. The reason being that it is designed to be driven by a balanced pair of signals, having equal amplitudes but opposite polarities, but the design of the amp apparently is such that when a single-ended signal is provided to its balanced input, one of those polarities ends up being MIA (missing in action) at the output stage.

BTW, given all of that some may wonder why the OP reported that the problem remained when he substituted a single-ended tube amp for the Ref 150. There are two possibilities that occur to me. Either a second problem has been present which resulted in similar symptoms (as I speculated in my 8-12-14 post), or the substitute tube amp was clipping simply because it was not powerful enough for the particular speakers at the particular volume level.

Best regards,
-- Al
More to discover