Electrical Panel Grounding

Eric - thanks fro the input.

Hair(;o

Jea - I read the article, and there is a bit fro me to learn. Thanks for your trouble to forward the link.

Jea - I read the article, and there is a bit fro me to learn. Thanks for your trouble to forward the link.

I should have mentioned you only need to read about the first 36 to 38 pages of the white paper.

I also should have asked you, in my last post, what country do you live in?  Earth ground is earth ground the world round but how it is accomplished/done/required varies. My comments are for the USA.

Here is a video on the subject of the use of an Auxiliary Grounding Electrode. It really serves no purpose and can cause damage to electronic equipment if used in the event of a nearby lightning storm.

https://www.youtube.com/watch?v=WlnFNTay-9Q

.

Jea - that youtube is exactly what I needed to know. This forum is amazingly helpful because a handful of people, like you, care enough to share.

I live in Denver with my wife, Lori. My system consists of a custom built pre-amp using two B29 tubes and two small front end Mullards. It is with transformer or OTL switchable circuitry, and switchable capacitance so I can tune to the source.
CD's need less and Vinyl more.

The amps are custom made with two 6C33C tubes per monoblock, 4 Mullards for the ancillary functions and a fairly massive output transformer. Class A/B with a solid 60W per side and 5 separate transformers for the various required voltages.

These amps are plenty to power my Soundlab U-2s. I prefer the U-2s 6' x 3' size over its larger brethren. These have been modified is several ways not easy to explain.

All running Audioquest cables, mostly silver over copper. I know that is way more than you asked, but I somehow thought you might find it interesting. One day I do a post on the pictures/system page, as the room is covered with my own acoustic diffusion and absorption panels which were sized and located by ear and trial and error. If you ever want to build your own, I do have some useful tips that will save you from learning the hard way like I did. And they work better than any of the stuff I tried that was made commercially at about 1/10th the cost.

wgutz ,

Thanks for your informative response.

The reason I asked in an earlier post what country you live in is because when I checked your profile, country was listed as N/A. You might want to change that to USA.

Now that I know you live in the US I have a few questions for you regarding the AC power delivery system used to feed your audio equipment.

What manufacture of sub panel are you using? Copper or aluminum bus?

Feeder size wiring feeding the sub panel?

Sub Panel wired 120/240V?

Approximate length of dedicated branch circuit wiring from the sub panel to the receptacle outlets feeding the audio equipment? (Up down and all around)

Type of branch circuit wiring used?
Example:
2 wire with ground NM-B cable? (Romex is a trade name). If romex how was the cabling ran through joists and or wall studs? Though a common bored hole or individually bored holes? If separate bored holes how far apart were the holes apart from one another? There in Romex cables kept separated from one another.

3 conductor MC armor cable? Aluminum or steel armor?

Conduit with wire loosely pulled into the conduit? If this wiring method was used was a separate conduit used for each 120V dedicated branch circuit?

Are all the dedicated circuits fed from the same line, leg, from the sub panel that feeds audio equipment that is connected together by wire interconnects? All fed from Line 1 or all from Line 2. (Not from Line 1 and Line 2.)

What are you using for wall outlet duplex receptacles? Manufacture, style and or series number? Plated contacts? Type of plating?
What material is the supporting back strap made of? Steel? Brass, other?

What are you using for cover plates for the wall duplex outlet receptacles?
Plastic? Flexible nylon? Stainless Steel? Other?

All the above can have an impact on the sound of your audio system.
.