...And if the speakers are measured at 2.83 Volts, as the impedance numbers go up, the power (Watts) of a ss amp output is reduced, as the efficiency of the speakers are correspondingly increased. All of which should work towards constant linear speaker output. Also consider that it's easier to make speakers with a more constant lower numerical impedance, than it is to make speakers with a more constant higher numerical impedance. Furthermore, wave form fidelity seems to be an elusive quality for speakers with higher numerical impedance/efficiency specs to achieve.
Speaker choice: impedance, sensitivity, and tubes
Looking at most speakers' specifications I cannot help but notice that very few are rated 8 ohms, and most dip well below their nominal specifications at certain frequencies. This makes makes me wonder how audiophiles with tube amplifiers select their speakers. Most tube amps have 8 and 4 ohm taps only, and from what I understand tube amps don't take kindly to dips in impedance. Is there a rule to abide by when selecting a speaker to match well with a tube amp when it comes to impedance?
Same with sensitivity. Perhaps not as important as impedance, but a lot of popular brands out there have disappointingly low sensitivity (85-86 dB). Why is that? I never understood it since the higher sensitivity, the easier it is to drive a speaker without having to have a beast of an amp. Seems all manufacturers should be striving to design their speakers to have higher sensitivity. Is is more expensive to make speakers with higher sensitivity?
Case in point, I own two pairs of speakers, one rated 88 dB and the other 91 dB. The 91 dB pair has an impedance of 8 ohms flat (according to the manufacturer) while the 88 dB pair has a nominal impedance of 6 ohms (not sure about dips). The difference is quite dramatic in terms of volume on my 180 watt tube amps. I often have to crank the volume way up to get sufficient loudness level in my rather small listening room (11x12) with the less efficient pair. That to me is crazy. The speakers are my fall-back pair from my digital past, and knowing how they behave, I'd never purchase them for my all-analog system today.
So as I'm thinking of upgrading my speakers, I'm quite perplexed about finding a speaker that would match well with my tube monoblocks - provide an easy load and good loudness level without strain. I've been considering giving Harbeths a shot, but I'm really turned off by their low sensitivity of 85 dB (30.1) and impedance of 6 ohms. How big an amp would I need if speakers with a sensitivity of 88 dB barely generate sufficient volume with 180 watts per channel?!
Can anyone explain in technical terms how tube amps handle speaker impedance and, secondarily, sensitivity? And perhaps more important from the practical standpoint - how does one select a speaker to match a tube amp?
Same with sensitivity. Perhaps not as important as impedance, but a lot of popular brands out there have disappointingly low sensitivity (85-86 dB). Why is that? I never understood it since the higher sensitivity, the easier it is to drive a speaker without having to have a beast of an amp. Seems all manufacturers should be striving to design their speakers to have higher sensitivity. Is is more expensive to make speakers with higher sensitivity?
Case in point, I own two pairs of speakers, one rated 88 dB and the other 91 dB. The 91 dB pair has an impedance of 8 ohms flat (according to the manufacturer) while the 88 dB pair has a nominal impedance of 6 ohms (not sure about dips). The difference is quite dramatic in terms of volume on my 180 watt tube amps. I often have to crank the volume way up to get sufficient loudness level in my rather small listening room (11x12) with the less efficient pair. That to me is crazy. The speakers are my fall-back pair from my digital past, and knowing how they behave, I'd never purchase them for my all-analog system today.
So as I'm thinking of upgrading my speakers, I'm quite perplexed about finding a speaker that would match well with my tube monoblocks - provide an easy load and good loudness level without strain. I've been considering giving Harbeths a shot, but I'm really turned off by their low sensitivity of 85 dB (30.1) and impedance of 6 ohms. How big an amp would I need if speakers with a sensitivity of 88 dB barely generate sufficient volume with 180 watts per channel?!
Can anyone explain in technical terms how tube amps handle speaker impedance and, secondarily, sensitivity? And perhaps more important from the practical standpoint - how does one select a speaker to match a tube amp?
- ...
- 22 posts total
- 22 posts total