imhififan
Responses from imhififan
| Thiel Owners For the visually inclined among you I have posted some photos on the diy audio forum.https://www.diyaudio.com/forums/multi-way/332679-thiel-cs2-4-xover-schematics.html#post5683434 @holco Very nice! thanks for sharing, would you please upload yo... | |
| Is there an rca input selector box audio only 2ch in 1 out? Maybe this is what you looking for: https://soundapproach.com/rek-o-kut-low-noise-stereo-phono-aux-switch.html | |
| Modifying Philharmonic 3 crossovers When I upgrade speaker crossover inductors, I like to change iron core inductor to air core. Air core inductor will be much bigger than iron core in order to keep the DCR as close as possible. | |
| Main L R speaker connection from seperate amps Niles Audio SPK-1 | |
| Side by side comparison of HT processor possible? Please be caution not all power amp can connect both SE and XLR at the same time! https://forum.audiogon.com/discussions/using-rca-xlr-connections-at-same-time-on-ampIf one of your pre/pro comes with a multi channel input will make life easier. | |
| Measuring impedance with multimeter For non EE types, what sort of equipment would be needed then to get a reasonably accurate measurement? https://studiosixdigital.com/impedance-meter-and-sweep-v.html or http://audiojudgement.com/loudspeaker-impedance-measurement/ | |
| This question is aimed to TRUE Elec Engineers, not fuse or wire directionality believers. 1.5V across 6 Ohms = 0.25A or 0.325 Watt Correction: 1.5V across 6 ohms = 0.25A or 0.375 Watt I think the current is pass through the tweeter voice coil and charge up the cap, if there's 80VDC the voice coil will blow in seconds. | |
| This question is aimed to TRUE Elec Engineers, not fuse or wire directionality believers. the driver was working, prior to being connected to a 33uF, non-polarized film cap and a C cell. It was reading 6 Ohms(correct nominal, according to the tweeter’s label), before it opened up. 1.5V across 6 Ohms = 0.25A or 0.325 Watt Back EMF? ... | |
| Thiel Owners Hi andy2, what is your opinion on the 1uF foil caps (C2 and C7), why JT omitted it in the SE crossover? http://www.hifishock.org/galleries/speakers/thiel/cs2.4se-2-thiel.jpg https://www.diyaudio.com/forums/attachments/multi-way/662210d1518507957-t... | |
| Thiel Owners How wide is the slot and how deep from the inside / back to the start of the flare? Is the inside edge eased / rounded in any way? The slot is about 1/2" wide x 12" long, inside the speaker there’s a about 1" thick x 2.5" height wooden wall around... | |
| Leak Stereo 30 integrated amplifier Sorry Ed, my links didn't do any good, it doesn't make sense if I suggests to buy a set of gauge pins just to measuring two holes. Maybe a set of drill pits can give you the measurements needed.Regards | |
| Leak Stereo 30 integrated amplifier Could be this one: https://www.ebay.co.uk/itm/TWO-PIECES-OF-2-PIN-SPEAKER-PLUGS-FOR-VINTAGE-VALVE-AMPLIFIER-/3027846084... Description shown 2.9 and 2.1 mm Dia. and 8 mm apart. | |
| Leak Stereo 30 integrated amplifier https://www.ebay.com/i/232841106775?chn=ps | |
| This question is aimed to TRUE Elec Engineers, not fuse or wire directionality believers. Accuphase http://www.accuphase.com/pdf/p-4500_e.pdf https://www.widescreenaudio.be/wp-content/uploads/2017/11/e-650_protection_circuit_3.jpg | |
| Which amp will cause a larger increase in electric bill? If sitting idle (power on), which will cost more, a class A 100 watt (Threshold) vs a 250 watt A/AB (Threshold)? I have both and a few more. I'm not worried about electric bill, just wondering. Kill A Watt |