keppertup
Responses from keppertup
| I’m gob smacked. What were you’re aha moments? Curtesy of Audiogon discussion forum:Modification of my thirty year old Magnepan MG IIIa’s due to generosity of Peter Gunn.Installation of DYI interconnects derived from friendly and patient input from Steve Reeve and Joe Levy.Installation of 0 AW... | |
| could somebody help me out on the benefits of expensive phono and speaker cables? Tablejockey,Your linked article by Harry Marynard is very informative.Harry describes the relationship between wire resistance, speakers’ varying impedance and the amplifier’s damping factor. These issues were addressed in the posts by b4icu refe... | |
| Speakers positionning Elizabeth, How far apart are your 20.7’s inside edges? | |
| No one actually knows how to lculate what speaker cable they need Dear Professor Michael,Please find photos of the cable I built as a result of your tutelage at the following links:https://imgur.com/a/12C7MQMhttps://imgur.com/a/vIL3qs0I hope this helps you and your disciples.All the Best | |
| No one actually knows how to lculate what speaker cable they need Granny ring,If you use the terminal ring/spade linked above, you can crimp the terminal with 8” channel locks. The medal is soft. Alternatively, Amazon has $15 crimping tools, including one that has a cradle and piston you hit with a hammer. I ... | |
| No one actually knows how to lculate what speaker cable they need Dear Professor (b4ic),I replaced DIY 5 foot 16 AWG silver ladder line. Have previously used a variety of commercial Helix design, solid flat wire and braided multi-stranded wires insulated and in multiple sleeves. Alll 12 AWG, 5 to 8 foot length... | |
| No one actually knows how to lculate what speaker cable they need Dear b4icu,I purchased 25 feet of 0 AWG form a supplier on eBay for $45 ($12 shipping) and four brass (supposedly gold plated) battery connectors ($7.49).I constructed four five foot cables in just over one hour. Battery connectors were converted... | |
| No one actually knows how to lculate what speaker cable they need Dill,You are correct, $23 buys clad aluminum. Thanks for educating me.I will order pure copper for $69.Gratefully yours | |
| No one actually knows how to lculate what speaker cable they need Dear Ganainm,Please a look at the work of Steve Reeve (image99.net, click on Audio Alchemy) regarding noise created by parallel + and - wires. Steve’s approach to a solution is different. I have assembled his cables and they are very good. My e... | |
| No one actually knows how to lculate what speaker cable they need Ganainm,Google: Monsterslayer.com for silver wire. Scroll to the bottom of their ordering form to find the .999 wire. Or, just call them. Very courteous staff.Given your background, I would be most interested in your feedback on copper vs silve... | |
| No one actually knows how to lculate what speaker cable they need Solder bare wire to speakers bare wire to custom crossover and form a soldered wire hook for amp screw clamp terminal. Any suggestions? | |
| No one actually knows how to lculate what speaker cable they need Ebay is selling 25 feet of 0 AWG copper wire for $23. I will buy it, install it and report back. I have five feet of cable between amp and speakers. Any other instructions? For me the hobby is about experimenting. | |
| No one actually knows how to lculate what speaker cable they need I experience the same results with the silver wire ladder design driving a second system consisting of a Hegel H200 integrate amp driving Aria A speakers (Joe D’Appolito three-way design employing Cabasse cone woofer and Accutron ceramic drivers).... | |
| No one actually knows how to lculate what speaker cable they need I have tried many cables to drive modified Magnepan MG IIIa’s with a Pass Labs 250.5. The best so far are DIY five foot cables made with 16AWG .999 pure solid silver inside 1/4” poly sleeve connected directly without termination to amp and speake... | |
| Switched from RCA to XLR Interconnects - WOW With help from the work and advice of Steve Reeve, Joe Levy and Nelson Pass I have designed and built DIY “Ribbon XLR interconnects.” The design consists of three 39” 11ga Teflon tubes layed out parallel 1” from each other and sandwiched between ... |