Ohm Walsh Micro Talls: who's actually heard 'em?


Hi,

I'd love to hear the impressions of people who've actually spent some time with these speakers to share their sense of their plusses and minuses. Mapman here on Audiogon is a big fan, and has shared lots on them, but I'm wondering who else might be familiar with them.
rebbi
Coot,

If it is the lowest notes of organ music that you are looking for, make sure your electronics, particularly pre-amp, is up to the task. I have found that to make the biggest difference with my OHMs over times.

My current ARC sp16 tube pre-amp is a wonderful sounding pre-amp, but not the most extended for low pipe organ notes. My old "mid-fi" Carver pre-amp was much better in that regard, but not in much else.

You might want to assess what you have currently in that regard and compare on paper to other options.

I would make sure that is covered first before doing anything else.

There may also be big differences in terms of low frequency response and distortion with source gear, particularly turntables and carts, more so than modern good quality digital.

At least that has been my experience with pre-amps and the OHMs with pipe organ music. Pipe organs aside, it does not matter nearly as much. If I listened to pipe organ music more often, I would be considering a different pre-amp I think, probably a very good SS one. It is good enough as is, but I have heard it can be much better, with my OHM 5s and in my room.

Pipe organs push the edge for low end extension versus pretty much anything else, so not just anything will do there anywhere in teh signal chain. Its not a huge consideration for many these days, so do not assume that just any gear is up to the task.
Marty,

I agree that adding a sub and offloading work from main speakers and amps significantly reduces what is demanded from both amp and speakers in most every case, not just OHM, and if done right can only be of benefit, if one chooses to go that way.

As I know you know, it's the "done right" part that is the challenge, but you more than most anyone here seem to have done your homework and found a good way to do it right.
In summary, I have heard where my OHM 5s in my room with the right gear in front of them can do an excellent job alone on the lowest notes of pipe organs, shaking hte rafters in the process. Top notch low end extension in source gear and enough power to go along with it are the keys.

Power demand increase exponentially at lower frequencies, so I would think 250W/ch or more for larger OHMs in a larger space to start to be where one would want for pipe organ notes that shake the rafters (as they should).

Damping factor of the amp is also significant for this. Higher damping might make bass tighter and more articulate, and lower damping will loosen things up more and help to get teh room vibrating.

My current setup is more towards the former than the latter these days.

But when I started out with my 5s off Carver m4.0t power amp (tube like sound, low damping) and matching Carver pre-amp, the rafters shook to the point where I would be concerned about things starting to fall off the walls and other similar problems.

Now its leaner and meaner, and not as loosely damped in the bass, but when I get things up to proper level for pipe organ and such, the lock key sitting on a narrow ledge nearby usually ends up on the floor still. And the sound is rock solid and clear, with no sign of breakup or distress EVER.

That is all with no subs in the picture.

Toss a couple of those in then get them set up right and you will likely take a nice shortcut to the place you seek.

So far, I have not felt the need, but do I do get the urge to try to push the limits from time to time....
I also just thought to mention that cabinet volume is a big factor with teh OHM Walshes along with driver size in terms of being able to deliver the goods down to 20hz.

I have never seen John advertise any Walsh models to extend below 20hz (few if any vendors ever do), but I am not sure it is not possible with the larger Walsh cabinets and drivers.

I like the older pyramidal shaped OHM cabinets in this regard in particular in that they tend to be wider and have greater volume per height accordingly, compared to the newer sleeker looking cabinets. Not to mention no || sides. All Walshes sound best when listened to from driver level or above, so narrower cabinets must be taller to have same volume. Taller will not work as well if listening from typical chair level closer to the speakers rather than at more of a distance, as is more possible in a larger room.

I prefer the older pyramid shaped cabinets on paper for all these reasons myself. Not to mention, they can be had for less than new ones in that when available they are essentially recycled and refurbed.

JS hit the bullseye with his Walsh design. Same sound scales as needed, old cabs can be re-used to offer a discount, plus all the rest. Very smart. No other speaker line can make those claims, I think.
32-ft pipe = 16Hz. Not that uncommon in large organs.

No argument, Coot,

I was merely pointing out that, of the half dozen or so pipe organ recordings that I own, only one - an SACD I purchased at the Cathedral in Passau, Germany (home of the largest pipe organ in Europe at that time) - actually has meaningful signal below 35hz.

One of my hobbies over the last several years has been measuring in-room response with my RTA and StudioQ software. Just to see how low my recordings go, I measured the pipe organ recordings (Sudio Q can be set to show lowest frequency/highest frequency, etc). On sweeps, my system will hit 25hz with no roll-off at 80db. The SACD referenced above is the only music recording that I've tested that dips below 30hz, tho it did get down into the 20ish hz region IIRC.

Lots of soundtracks go very low, and there's no question that a pipe organ can go that low, but there's a major question in my mind how many pipe organ recordings go that low.