alanpiga
Responses from alanpiga
| SUT for Lyra Clavis Evolve 99 Using the Clearaudio Stradivari with the 40 ohms tap (10x voltage) seems perfect "on paper" as Flyfish2002 explains it but as he says it is going to be difficult to find a transformer for the Lyra. The problem is the volume pot of the preamp has t... | |
| SUT for Lyra Clavis Evolve 99 I don't know the price of the Nagra equipment but I guess I am more into buying a SUT for cost savings. I have a perception of Nagra being expensive equipment. | |
| SUT for Lyra Clavis Evolve 99 The Air Tight ATC-1 preamp doesn't offer any adjustment in the phono stage loading or capacitance. I have read of people changing the 47 kohm resistor in other preamps assuming that the ATC-1 has one which I bet it does, but I have never played wi... | |
| SUT for Lyra Clavis Evolve 99 Sorry I shuld've said all SUT's specified with lower IMPEDANCE are designed for low output voltage cartridges(the low impedance sut's higher gain charaacteristic is appropiate with these)and the Lyra is a medium output cartridge therefore the volu... | |
| Electrical problems? This is new:When the tip of the neddle touches the platter you hear noise. A new noise. It clearly goes away when you lift the neddle from the platter. Or the record. Basicaly, the grounding of the turntable I think has been done. There is a wire ... | |
| Electrical problems? Connecting the cable from the bottom of the turntable at the bearing to the power adapter's ground terminal didn't help eliminate the hum. The system is humming as hell when switched to phono stage; once when opening the bedroom door there was a s... | |
| Electrical problems? I spoke to Chris at Teres and his suggestion is to connect the wire from the screw at the bottom of the table which I believes connects the bearing to the power adapters ground.But he suggested that it may not be possible to eliminate the static b... | |
| Electrical problems? I have checked the cartridge clips and their connection appear to be allright. As far as the internal wire of the tonearm I haven't ventured to dissasemble it. I could try and use another arm wand and discard the wiring in the arm wand as the one ... | |
| cartridge for Eminent Technology ET2 tonearm? I ordered the DL-103R from Action Accessories in Linden, New Jersey. It will take 14 days to get here they told me. I read somewhere about a place called phonophono with excellent prices but I believe it is in Europe.As far as cartridge loading, I... | |
| cartridge for Eminent Technology ET2 tonearm? I ordered the Denon DL-103R cartridge based on your advice, folks, thank you, sincerely.I really don't want to spend a lot of money in this and I am happy to "hear" that technically it won't be a mismatch.Just what I needed to hear!!!!!And I will ... | |
| Power amplifier for NHT 2.5i speakers? Well, I am crazy but I am playing the NHT 2.5i's with a pair of Wavelength Gemini Twins now, they play better than the Parasound, Better bass, with 2.5 watts per channel!!!!believe or not, and the sound, a lot more quality.I had bought a pair of S... | |
| Best speakers for Parasound HCA-1000A power amp? 8 ft. high ceiling. | |
| Best speakers for Parasound HCA-1000A power amp? The room is 24 ft. long by 14.5 ft. wide with the speakers located along the short wall. Half one 24 ft. side is open to the kitchen and a corridor. There are two windows, 6 ft. long, in the other 24 ft. wall. Concrete slabs with glued floor wood ... | |
| Power amplifier for NHT 2.5i speakers? Daveyguitar:Can you comment on the bass performance using the McCormack DNA 0.5? | |
| Power amplifier for NHT 2.5i speakers? Adding to the above paragrarh, the ceiling is at 8 ft. high. The construction is concrete slabs with glued parket flooring. Walls are sheetrock on metal studs. |